Design Store

ADC example for use with Board Test System Monitor Panel  

CategoryDesign Example
NameADC example for use with Board Test System Monitor Panel
Description10M50DA device has two analog-to-digital converters (ADC) which can be used to monitor the internal temperature of the die and support external analog signal conversion. So this design example is used to check out FPGA embedded ADC components alongside with external DAC and potentiometer on the board. Please download the installer of MAX 10 FPGA development kit and use BTS GUI to try it out.
Operating SystemNone
IP Core
IP CoreHeading
Avalon ALTPLLPLL
PIO (Parallel I/O)Peripherals
altera_jtag_avalon_masterSystem
Avalon-ST Bytes to Packets ConverterStreaming
Avalon-ST Channel AdapterStreaming
Avalon-ST Single Clock FIFOOn Chip Memory
Avalon-ST JTAG InterfaceSerial
Avalon-ST Packets to Bytes ConverterStreaming
Reset ControllerClocks; PLLs and Resets
Avalon-ST Timing AdapterStreaming
Avalon Packets to Transaction ConverterStreaming
MM InterconnectMerlin Components
Avalon-ST AdapterStreaming
Avalon-ST Error AdapterStreaming
Memory-Mapped DemultiplexerMemory-Mapped
Memory-Mapped MultiplexerMemory-Mapped
Avalon-MM Slave AgentMemory-Mapped
Avalon-MM Slave TranslatorMemory-Mapped
Avalon-MM Master AgentMemory-Mapped
Memory-Mapped Traffic LimiterMemory-Mapped
Avalon-MM Master TranslatorMemory-Mapped
Memory-Mapped RouterMemory-Mapped
Altera Modular ADC corePeripherals
Altera Modular ADC Control corePeripherals
Altera Modular ADC Sample Storage corePeripherals
Altera Modular ADC Sequencer corePeripherals
Version1.0
FamilyMAX 10
Device10M50DA
Documentation
DocumentDescription
ADC_Convertor_Using_MAX_10_FPGA_Development_KitA simple design spec for ADC design example
Development KitMAX 10 FPGA Development Kit
Installation Package

Note: After downloading the design example, you must prepare the design template. The file you downloaded is of the form of a <project>.par file which contains a compressed version of your design files (similar to a .qar file) and metadata describing the project. The combination of this information is what constitutes a <project>.par file. In releases 16.0 or newer, you can simply double click on the <project>.par file and Quartus will launch that project.

The second means to bring up the project template is through the New Project Wizard (File -> New Project Wizard). After entering the project name and folder on the first panel, the second panel will ask you to specify an empty project or project template. Select project template. You will see a list of Design Templates projects that you have loaded prior as well as various "Baseline Pinout Designs" that contain the pinout and settings for a variety of development kits. If you don't see your design template in the list, click on the link that states install the Design Templates circled below:


Browse to the <project>.par file you downloaded, click next, followed by Finish, and your design template will be installed and displayed in the Project Navigator pane in Quartus.

Note: When a design is stored in the Design Store as a design template, it has been previously regression tested against the stated version of Quartus software. The regression ensures the design template passes analysis/synthesis/fitting/assembly steps in the Quartus design flow.

At the command-line, type the following command:

quartus_sh --platform_install –package <project directory>/adc.par

Once the process completes, then type:

quartus_sh --platform –name adc

Download
Total Downloads171 (From 18 Jul 2016 to 20 Sep 2017)
Quartus II VersionDownload Quartus II v16.0
Quartus II EditionStandard
VendorAltera


Last updated on July 18, 2016, 11:46 a.m.