Design Store

Nios II Full Featured Reference Design - BeMicro  

CategoryDesign Example
NameNios II Full Featured Reference Design - BeMicro
DescriptionThis is a comprehensive design example which demonstrates how to use the following interfaces on the BeMicro Max 10 FPGA Evaluation kit:
(i) Accelerometer
(ii) Temperature Sensor
(iii) DAC
(iv) ADC
(v) Serial Flash
Operating SystemBareMetal
IP Core
IP CoreHeading
Avalon ALTPLLClocksPLLsResets
PIO (Parallel I/O)Other
Nios II Gen2 ProcessorNiosII
Nios II Gen2 Processor UnitNiosII
On-Chip Memory (RAM or ROM)OnChipMemory
IRQ MapperQsysInterconnect
JTAG UARTConfigurationProgramming
MM InterconnectQsysInterconnect
Avalon-MM Slave AgentQsysInterconnect
Avalon-ST Single Clock FIFOQsysInterconnect
Avalon-MM Slave TranslatorQsysInterconnect
Avalon-ST AdapterQsysInterconnect
Avalon-ST Error AdapterQsysInterconnect
Memory-Mapped DemultiplexerQsysInterconnect
Memory-Mapped MultiplexerQsysInterconnect
Avalon-MM Master AgentQsysInterconnect
Avalon-MM Master TranslatorQsysInterconnect
Avalon-ST Handshake Clock CrosserQsysInterconnect
Memory-Mapped RouterQsysInterconnect
Memory-Mapped Burst AdapterQsysInterconnect
Memory-Mapped Width AdapterQsysInterconnect
Memory-Mapped Traffic LimiterQsysInterconnect
Altera Modular ADC coreADC
Altera Modular ADC Control coreADC
Altera Modular ADC Sample Storage coreADC
Altera Modular ADC Sequencer coreADC
Reset ControllerQsysInterconnect
SDRAM ControllerExternalMemoryInterfaces
SPI (3 Wire Serial)SPI
JTAG to Avalon Master BridgeConfigurationProgramming
Avalon-ST Bytes to Packets ConverterQsysInterconnect
Avalon-ST Channel AdapterQsysInterconnect
Avalon-ST JTAG InterfaceQsysInterconnect
Avalon-ST Packets to Bytes ConverterQsysInterconnect
Avalon-ST Timing AdapterQsysInterconnect
Avalon Packets to Transaction ConverterQsysInterconnect
System ID PeripheralOther
Interval TimerPeripherals
Altera On-Chip FlashFlash
altera_jtag_avalon_masterQsysInterconnect
Version1.02
FamilyMAX 10
Device10M08DA
Documentation
DocumentDescription
Full Featured Reference Design User Guide-
Development KitBeMicro MAX 10 FPGA Evaluation Kit
Installation Package

Note: After downloading the design example, you must prepare the design template. The file you downloaded is of the form of a <project>.par file which contains a compressed version of your design files (similar to a .qar file) and metadata describing the project. The combination of this information is what constitutes a <project>.par file. In releases 16.0 or newer, you can simply double click on the <project>.par file and Quartus will launch that project.

The second means to bring up the project template is through the New Project Wizard (File -> New Project Wizard). After entering the project name and folder on the first panel, the second panel will ask you to specify an empty project or project template. Select project template. You will see a list of Design Templates projects that you have loaded prior as well as various "Baseline Pinout Designs" that contain the pinout and settings for a variety of development kits. If you don't see your design template in the list, click on the link that states install the Design Templates circled below:


Browse to the <project>.par file you downloaded, click next, followed by Finish, and your design template will be installed and displayed in the Project Navigator pane in Quartus.

Note: When a design is stored in the Design Store as a design template, it has been previously regression tested against the stated version of Quartus software. The regression ensures the design template passes analysis/synthesis/fitting/assembly steps in the Quartus design flow.

At the command-line, type the following command:

quartus_sh --platform_install –package <project directory>/BeMicro_full_reference.par

Once the process completes, then type:

quartus_sh --platform –name BeMicro_full_reference

Download
Total Downloads237 (From 03 May 2015 to 14 May 2018)
Quartus Prime VersionDownload Quartus Prime v15.0
Quartus Prime EditionStandard
VendorArrow


Last updated on Aug. 27, 2015, 12:31 a.m.

document.getElementById('links').onclick = function (event) { event = event || window.event; var target = event.target || event.srcElement, link = target.src ? target.parentNode : target, options = {index: link, event: event}, links = this.getElementsByTagName('a'); blueimp.Gallery(links, options); };